Shop – COPO Parts Direct

COPO CHARGING PORT

AC User — Fri, 20 Mar 2020 14:49:03 +0000

THIS KIT IS DESIGNED TO FIT INTO GEN 6 COPO’S TO ALLOW FOR EASY CHARGING OF YOUR BATTERIES. NO MORE BATTERY CHARGER CABLES HANGING OUT OF THE TRUNK AND DESTROYING YOUR PAINT AND TRUNK SEAL. THIS KIT IS MADE USING HIGH QUALITY 4 GAUGE WIRE AND EVERY KIT IS TESTED AND INSPECTED BEFORE IT LEAVES OUR FACILITY.

KIT INCLUDES:

FEMALE CHARGING PORT WITH #4 WIRE AND PRECRIMPED ENDS
MALE CONNECTOR WITH SPADES FOR USE WITH YOUR EXISTING BATTERY CHARGER
CRASH BAR SPACER FOR MOUNT INSTALLATION (SEE PICS)
CHARGING PORT MOUNT

PARACHUTE FLAG

AC User — Thu, 19 Mar 2020 13:25:45 +0000

COPO PARACHUTE FLAG

HIGH QUALITY CANVAS
FEATURES COPO GRAPHICS ON BOTH SIDES
INCLUDES ALL PICTURED HARDWARE

THERMOSTAT REPLACEMENT SPOOL

AC User — Thu, 12 Mar 2020 17:22:29 +0000

THIS SPOOL ELIMINATES THE THERMOSTAT IN LS ENGINES, GIVING YOU FULL FLOW TO THE RADIATOR THE MOMENT THE ENGINE IS FIRED. THIS ENSURES ADEQUATE COOLING WHILE RACING.

FITS LS3 WATER PUMPS 2009-2015
INCLUDES NEW OEM GM GASKET
FOR OFFROAD USE ONLY
THE 4 HOLES IN THE SPOOL EQUAL THE SAME AMOUNT OF AREA AS THE COOLANT HOUSING INLET TO ENSURE THERE IS NO LOSS IN COOLANT FLOW OR PRESSURE.

COPO STEERING WHEEL QUICK RELEASE KIT

AC User — Thu, 12 Mar 2020 13:39:24 +0000

THIS KIT INCLUDES THE FOLLOWING:

6 BOLT QUICK RELEASE HUB
COPO STEERING WHEEL
ALL NECESSARY HARDWARE TO INSTALL

NOTE: INSTALLATION REQUIRES WELDING

COPO FENDER EMBLEM SET

Mike Lawrence — Tue, 03 Mar 2020 16:09:19 +0000

FITS GEN 6 COPO 2016-2020

AEROMOTIVE 3.5 GPH BRUSHLESS DROP IN FUEL PUMP

Mike Lawrence — Tue, 25 Feb 2020 18:19:59 +0000

INCLUDES CONNECTOR KIT FOR COPO HARNESS

The Pro-Series performance you expect and more:

Fuel injected engines:
– up to 2400 FWHP – naturally aspirated
– up to 1800 FWHP – forced air induction
Carbureted engines:
– Up to 2600 FWHP – naturally aspirated
– Up to 2000 FWHP – forced air induction
E85 Compatible, reduce max FWHP by 30%
Lighter than the traditional Pro-Series pump.
Reduced current draw at higher, EFI pressures.
Extended service life in methanol and ethanol.
New integral spur-gear pumping mechanism.
90-PSI continuous operating pressure and up to 150-PSI peak pressure, base plus boost.
Integral, external brushless controller for clean installation, cooler fuel and enhanced reliability.
ORB-10 outlet port.
Requires straight 12-VDC to 16-VDC power supply.
Not compatible with pulse modulated systems or fuel pump speed controllers.

REAR FASCIA BURNOUT GUARDS

Mike Lawrence — Fri, 21 Feb 2020 18:59:56 +0000

Tired of scrapping rubber off of your rear fascia every time you go to the track?

These fascia guards keep the rubber off of the painted surfaces of your COPO to keep your paint looking right.

Fits Gen 6 COPO

TWO STEP KIT PEDAL MOUNTED

Mike Lawrence — Thu, 13 Feb 2020 15:13:42 +0000

THIS IS A PEDAL MOUNTED TWO STEP SWITCH THAT PLUGS DIRECTLY INTO YOUR COPO WIRING HARNESS.

WE TYPICALLY RECOMMEND TO INSTALL THIS SWITCH ON THE TOP LEFT OR BOTTOM LEFT SIDE OF THE BRAKE PEDAL (DRIVERS PREFERENCE)

FRONT TOW HOOK

Mike Lawrence — Thu, 13 Feb 2020 13:47:02 +0000

Every COPO racer needs one of these hooks. It can make loading in the trailer easier and the right way to tow your COPO at the track

TWO STEP PRESSURE SWITCH

Mike Lawrence — Wed, 12 Feb 2020 20:11:53 +0000

STARTING LINE 2-STEP RPM SYSTEM
STANDARD THROTTLE SWITCH CONTROL
BRAKE PRESSURE ACTIVATED CONTROL
INTEGRATED INTO THE COPO WIRING HARNESS